next up previous contents index
Next: 4.14 Specifying area fill Up: 4. General features Previous: 4.12 PostScript Features   Contents   Index

4.13 Specifying pen attributes

A pen in GMT has three attributes: width, color, and texture. Most programs will accept pen attributes in the form of an option argument, with commas separating the given attributes, e.g.,


-W[width[c$\vert$i$\vert$p$\vert$m]],[color],[texture[c$\vert$i$\vert$p$\vert$m]]

$\rightarrow$
Width is by default measured in units of the current device resolution (i.e., the value assigned to the parameter DOTS_PR_INCH in your .gmtdefaults4 file). Thus, if the dpi is set to 300 this unit is 1/300th of an inch. Append c, i, p, or m to specify pen width in cm, inch, points (1/72 of an inch), or meters, respectively. Note that a pen thickness of 5 will be of different physical width depending on your dpi setting, whereas a thickness of 5p will always be 5/72 of an inch. Minimum-thickness pens can be achieved by giving zero width, but the result is device-dependent. Finally, a few predefined pen names can be used: default, faint, and {thin, thick, fat}[er$\vert$est], and obese. Table [*] shows this list and the corresponding pen widths.

Table: GMT predefined pen widths.
Pen name   Width Pen name Width
faint 0 thicker 1.5p
default 0.25p thickest 2p
thinnest 0.25p fat 3p
thinner 0.50p fatter 6p
thin 0.75p fattest 12p
thick 1.0p obese 18p


$\rightarrow$
The color can be specified in five different ways:
  1. Gray. Specify a gray shade in the range 0-255 (linearly going from black [0] to white [255]).
  2. RGB. Specify r/g/b, each ranging from 0-255. Here 0/0/0 is black, 255/255/255 is white, 255/0/0 is red, etc.
  3. HSV. Specify hue-saturation-value, with the former in the 0-360 degree range while the latter two take on the range 0-14.10.
  4. CMYK. Specify cyan/magenta/yellow/black, each ranging from 0-100%.
  5. Name. Specify one of 663 valid color names as defined in the X11 color table4.11. A very small yet versatile subset consists of the 29 choices white, black, and [light$\vert$dark]{red, orange, yellow, green, cyan, blue, magenta, gray$\vert$grey, brown}.

$\rightarrow$
The texture attribute controls the appearance of the line. ``.'' yieds a dotted line, while a dashed pen is requested with ``-''. The lengths of dots and dashes are scaled relative to the pen width (dots has a length that equals the pen width while dashes are 8 times as long; gaps between segments are 4 times the pen width). For more detailed attributes including exact dimensions you may specify string:offset, where string is a series of numbers separated by underscores. These numbers represent a pattern by indicating the length of line segments and the gap between segments. The offset phase-shifts the pattern from the beginning the line. For example, if you want a yellow line of width 0.1 cm that alternates between long dashes (4 points), an 8 point gap, then a 5 point dash, then another 8 point gap, with pattern offset by 2 points from the origin, specify -W0.1c,yellow,4_8_5_8:2p. In general, the texture units can be specified in dpi units, cm, inch, points, or meters (see width discussion above).
Table 4.5 contains additional examples of pen specifications suitable for, say, psxy.


Table 4.5: A few examples of pen specifications.
Pen example Comment
-W0.5p Solid black line, 0.5 point thick
-Wgreen Solid green line with default width
-Wthin,red,- Dashed, thin red line
-Wfat,. Fat dotted line [black]
-W0.1c,120-1-1 Green (in h-s-v) pen, 1 mm thick
-Wfaint,100/0/0/0,..- Very thin, cyan (in c/m/y/k), dot-dot-dashed line



next up previous contents index
Next: 4.14 Specifying area fill Up: 4. General features Previous: 4.12 PostScript Features   Contents   Index
Paul Wessel 2006-05-31